How do I reset my OBi100?
How do I reset my OBi100?
The Under-Panel Reset Button Using the end of a paperclip, press it into the raised hole, located on the bottom-left side of the OBi100. As illustrated below, it is located on the left side of the OBi100 ID label, next to the 9-digit ID/phone number. Press and hold for at least a full 10 – 15 seconds.
What is OBi attendant pin?
Auto Attendant 4 Digit PIN:� When this field is populated with a numeric four digit PIN, the auto attendant on the OBi will request callers enter this PIN in order to make new calls via any available service, e.g. Internet voice service provider, PSTN/land line gateway (on models so equipped), or the OBiTALK network.
How do I access my OBi302?
Access the web interface. By default, the username and password is admin / admin or admin / 72227. If you do not know the device login/password you may need to contact the vendor of the device.
How do I find my OBiTALK IP address?
Thanks. Re: How to locate OBI100’s IP address? The easiest way to read the OBi’s ip address is to pickup the phone attached to the OBi and dial *** for the IVR and then after the prompt enter 1 for Basic Network status which will give you an audio readout of the OBi’s local network ip address.
How do I reset an OBiTALK device?
Frequently Asked Questions
- Step 1: Remove the OBi From the OBiTALK Web Portal. Sign in to www.obitalk.com and select the device you are going to reset from the OBi Dashboard.
- Step 2: Reset the OBi Device Using the Physical Pin (Button) With a paper clip (or similar) depress the reset pin located at the bottom of the OBi.
How do I log into OBi200?
If you are trying to access the configuration pages via the local Web interface, type the IP address of the OBi200 into a computer browser and hit Enter. The UserID and default password are both “admin”.
Why is my OBiTALK not working?
Reboot both your router and the OBi device, then dial * * 9 222-222-222 again. Please try rebooting your router and the OBi device and check to see if calls are still dropping. If you are still experiencing dropped calls, please check with your service provider to see if there is a temporary service disruption.
How do I update my Obihai firmware?
When you are logged in, open the system management tab and go to the device update. Now, look for the firmware file that you’ve already downloaded and tap on the update button. As a result, it will be installed and OBi will be restarted, and when it switches back on, you can use the updated version.
How do I factory reset my OBi?
Step 2: Reset the OBi Device Using the Physical Pin (Button)
- With a paper clip (or similar) depress the reset pin located at the bottom of the OBi.
- While keeping the reset pin depressed, plug-in the power cord.
- After 10 seconds, the Power LED will start to flash green (slowly).
How do you reset Obihai?
Resetting an Obihai Adapter
- Using the end of a paperclip, depress the reset pin, located on the bottom-left side of the Obihai.
- While keeping the reset pin depressed, plug-in the power cord.
- The Power LED will turn red, then become solid green.
- Keep depressing the reset pin while this is occurring.
Where can I find the Obi log in Wizard?
The obitalk.com wizard can also be found in the Device Configuration area for your OBi – log-in to www.obitalk.com required. If you have configured your deive using any of the methods above DO NOT follow the instructions below.
What is the default setting for the OBi110?
The default setting had the OBi110 attempting to place calls using the PSTN port on the device. The relevant setting is: The default is PSTN. Select SP1 Service if you only have one SIP account configured on the device. Select Trunk Group 1 to have it attempt to place calls using SP1 first, then SP2.
Is the Obihai OBi100 a single port ATA?
The Obi100 is a single port ATA from OBihai Technology Inc. This device contains a single FXS port for use with a SIP provider. The device is simple to setup and can be configured and used in minutes. Additional advanced parameters are also available to end users through the admin interface.
How to get the IP address of an OBi100?
Start by dialing * * * from the connected phone, then press 1 to confirm your choice, this will return the IP address of your device being a number similar to 192.168.xxx.xxx. Once you get the IP address, enter it in the URL address bar “http://” of your Internet Browser to get access to the Graphic User Interface of the OBi100.